Polycell Expanding Foam Polyfilla 0,5 L
Polycell Expanding Foam Polyfilla , 0,5 L, 0,5 h, Depending on bead size & conditions, If the can is to be used again,...Lire la description complète ↓
| Date | Prix |
|---|---|
| 7 mai 2026 | 32,46 € |
| 7 mai 2026 | 25,86 € |
| 5 juin 2026 | 32,80 € |
| 8 juin 2026 | 25,86 € |
| 28 juin 2026 | 33,90 € |
| 1 juillet 2026 | 33,91 € |
Comparer les prix de Polycell Expanding Foam Polyfilla 0,5 L
Aucune Offre n'est disponible pour le moment
Information produit
Polycell Expanding Foam Polyfilla . Volume: 0,5 L, Le temps de séchage: 0,5 h, Note sur le temps de séchage: Depending on bead size & conditions. Largeur du colis: 80 mm, Profondeur du colis: 60 mm, Hauteur du colis: 240 mm. Couches par palette: 3 pièce(s), Produits par couche de palette: 216 pièce(s), Produits par palette: 648 pièce(s)
Produit
- Nom
- Polycell Expanding Foam Polyfilla 0,5 L
- Catégorie
- Mortiers de ragréage
- Marque
- Polycell
Caractéristiques
- Adapté à une utilisation à l'intérieur
- Oui
- Adapté à une utilisation extérieure
- Non
- Volume
- 0,5 L
- Le temps de séchage
- 0,5 h
- Note sur le temps de séchage
- Depending on bead size & conditions
- Nettoyage d'outils
- If the can is to be used again, bend nozzle and attach tip to the nib (see leaflet). When reusing, remove the nozzle tip from the nib and cut away any part of the nozzle tip that is blocked with hardened product. Then continue from step 2 above
- Comment utiliser
- 1) Remove cap carefully, holding can away from face. Carefully screw the nozzle fully onto valve. Do not force the nozzle onto the valve (refer to the Additional Safety Precautions below if the nozzle won't screw fully onto valve). 2) Moisten surface with water to help the foam cure and expand (e.g. with plant sprayer). 3) Shake can vigorously approx. 30 times to mix contents. 4) Apply light pressure first to check if valve is working properly. Vary pressure to adjust rate of foam release. Start filling from the lowest point shaking can occasionally during use. Do not overfill - the foam will expand to 2.5 times the initial volume. 5) If building up in layers, spray lightly with water between layers to help fully cure and maximise expansion. 6) Remove fresh foam spillage immediately with nail varnish remover (test on a concealed area first). Cured foam can only be removed mechanically. 7) Foam will be tack free in 15 minutes, surface dry in 30 minutes. It can be cut, sanded, plastered or painted after 12 hours. 8) If exposed to sunlight, the foam must be painted or coated.
- Comment conserver
- Store in a cool dry place away from frost, on a low shelf to avoid risk of accidental dropping (but keep out of reach of children). Once opened, the can must be used within 8 weeks.
- Préparation de surface
- Do not apply near naked flames or other sources of ignition. Turn off nearby electrical appliances before use and do not switch on until vapours have cleared. Ensure good ventilation during use. Do not apply in very cold or hot conditions (below 5ºC or above 25ºC). Do not use in areas where cured foam will be exposed to temperatures continuously above 60ºC (e.g. near heating appliances). Ensure surface and hole are clean and free of grease and loose material. Cover furniture, carpets and surrounding areas and mask off any brickwork.
Informations sur l'emballage
- Largeur du colis
- 80 mm
- Profondeur du colis
- 60 mm
- Hauteur du colis
- 240 mm
- Quantité
- 1 pièce(s)
Données logistiques
- Couches par palette
- 3 pièce(s)
- Produits par couche de palette
- 216 pièce(s)
- Produits par palette
- 648 pièce(s)
Avis clients
Faites-nous part de votre avis sur le produit ou consultez les avis des autres membres.